VSS error problem fix for EJ conversion in Brumby/Brat

VSS (vehicle speed sensor) fix for EJ conversion

Written by Thomas Paine - Phizinza

One of the things you encounter when doing an EJ conversion to your EA81 Subaru is the VSS problem. EA81's never had speed sensors expect for in the US and some other countries, so it's best to look at the speedo you have before worrying too much. This is just one solution to the problem, but it's easy and I believe won't cause a problem.

First off you need a EA82 speedo from the cluster. These have a small magnetic switch (reed switch) which gets 4 pulses a rotation of the speedo cable. The cable is geared 2 to 1 in the gearbox so it runs half speed of the output shaft on the gearbox, which is directly coupled to the propshaft. So you need 2 pulses a rotation of your propshaft. You also need 2 magnets to attach to the propshaft to give the reed switch the required magnetic pull to turn it on and off. I was in a rust so I cut up a speaker magnet (crude, but it works) and used two small chunks of it. You will want your magnets big enough to give the reed switch an open time of 1/6th to 1/4 of the rotation. Some where around 10mm x 10mm x 5mm should do it for each one.

*click images to enlarge*

Once you get the speed sensor from the EA82 speedo out it should look like this

Next up you need a mount to put the reed switch to that will put it right near the propshaft. You can do this is various ways but this is how I done it with a small piece or recycled piece of alloy bar.

Then you need to fit the reed switch to the bracket, I just cut off one of the original brackets on the circuit board and bent the other so it could be pop riveted to the new bracket. This also solved the connection shorting out issue as the brackets on the VSS are the "wires" so to say. I then cut a piece of gasket material to insulate the switch from the alloy bracket.

Once you've pop riveted the switch to the bracket solder on a couple of wires to the switch and then coat the whole lot in RTV silicone to keep it safe.

Then you need to find out where the magnets need to sit to close the reed switch. Do this by holding a ohm meter on continuity test setting and move the magnet near the switch. In my case the polls on my magnets worked best when they were off to the side of the switch. Just do more testing until you know where the bracket must sit to hold the switch in the right place. Then glue the magnets to the propshaft, one of each side exactly.

Mount the reed switch about 3mm away from the magnets so it's close enough but doesn't touch.

You then need to mount the switch and run a wire to the VSS pin on the ECU and a wire to GROUND (anywhere on your chassis will do.) This should fix the problem and you should have no problem I hope.

And there you have it. Your ECU should be happy as ever with the pulse code it gets.

Just for your information if you have 3.7 diffs and near standard tyres the rotations of your output and propshaft will be around 55 a second at 100kph / 60mph And your speedo cable will be half that.


Event Reports 4x4 Riverland Challenge 2009 4x4 Mud Dust & Music 09 4x4 Riverland Challenge 08 Victoria 4WD Trip June 09 New Articles AWD and Odd Sized Tyres Outback Low Range Conversion Windscreen, Spray then Wipe Storage and Sleeping System Project83 Intro - the idea and plan 4WD Conversion Fender cutting Radius Rod Mod CD Player install EA81 Concept Subaru's Bobbed Subaru Brumby 2005 Subaru Brumby/Brat 2door STi Convertible Forester Pickup Truck EA82 hatchback Other Photochops Subaru related Links Forums Ultimate Subaru Message Board Info Sites Subaru Off Road Off Road Subaru.com My Brat on CarDomain	Home - Forum - Merchandise! - Search - Offroading Subaru FAQ - General Definitions - Articles Archive - Links - Videos
	VSS (vehicle speed sensor) fix for EJ conversion Written by Thomas Paine - Phizinza One of the things you encounter when doing an EJ conversion to your EA81 Subaru is the VSS problem. EA81's never had speed sensors expect for in the US and some other countries, so it's best to look at the speedo you have before worrying too much. This is just one solution to the problem, but it's easy and I believe won't cause a problem. First off you need a EA82 speedo from the cluster. These have a small magnetic switch (reed switch) which gets 4 pulses a rotation of the speedo cable. The cable is geared 2 to 1 in the gearbox so it runs half speed of the output shaft on the gearbox, which is directly coupled to the propshaft. So you need 2 pulses a rotation of your propshaft. You also need 2 magnets to attach to the propshaft to give the reed switch the required magnetic pull to turn it on and off. I was in a rust so I cut up a speaker magnet (crude, but it works) and used two small chunks of it. You will want your magnets big enough to give the reed switch an open time of 1/6th to 1/4 of the rotation. Some where around 10mm x 10mm x 5mm should do it for each one. click images to enlarge Once you get the speed sensor from the EA82 speedo out it should look like this Next up you need a mount to put the reed switch to that will put it right near the propshaft. You can do this is various ways but this is how I done it with a small piece or recycled piece of alloy bar. Then you need to fit the reed switch to the bracket, I just cut off one of the original brackets on the circuit board and bent the other so it could be pop riveted to the new bracket. This also solved the connection shorting out issue as the brackets on the VSS are the "wires" so to say. I then cut a piece of gasket material to insulate the switch from the alloy bracket. Once you've pop riveted the switch to the bracket solder on a couple of wires to the switch and then coat the whole lot in RTV silicone to keep it safe. Then you need to find out where the magnets need to sit to close the reed switch. Do this by holding a ohm meter on continuity test setting and move the magnet near the switch. In my case the polls on my magnets worked best when they were off to the side of the switch. Just do more testing until you know where the bracket must sit to hold the switch in the right place. Then glue the magnets to the propshaft, one of each side exactly. Mount the reed switch about 3mm away from the magnets so it's close enough but doesn't touch. You then need to mount the switch and run a wire to the VSS pin on the ECU and a wire to GROUND (anywhere on your chassis will do.) This should fix the problem and you should have no problem I hope. And there you have it. Your ECU should be happy as ever with the pulse code it gets. Just for your information if you have 3.7 diffs and near standard tyres the rotations of your output and propshaft will be around 55 a second at 100kph / 60mph And your speedo cable will be half that.
	Contact Text and pictures on this site Copyright © 2005 Thomas Paine. All rights reserved. All copyrights are retained by original authors. If you wish to use a picture or quote the text off this site to your own site or to a online forum please ask for permission first. If you use anything off this site that may lead to damage of my reputation I will have to take the matter further. So do not piss me off! DISCLAIMER: Thomas Paine, www.OffroadingSubarus.com, does not warrant or make any representation regarding the use, or results of use of the information contained on and within this website as to its correctness, accuracy, currency or otherwise. Thomas Paine, www.OffroadingSubarus.com, expressly disclaim all liability or responsibility to any person using the information or advice contained on and within this website.